Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
Gulf Stream Owners RV Forum
 


Reply
 
Thread Tools Search this Thread Display Modes
 
Old 08-03-2010, 10:36 AM   #1
SugarRv
Junior Member
 
Join Date: Mar 2009
Location: Madison WI
Posts: 20
Default Leveling leg question

I have a 2003 Friendship Quattro with the Dewald leveling system. How do I remove the metal pad at the bottom of the leveling leg? I need to pound it flat after bending it on a rock recently.
__________________
2003 Friendship Quattro 41Ft
Cummins ISL 400
2012 Nissan Altima on Master Tow Dolly
SugarRv is offline   Reply With Quote
Old 08-04-2010, 04:47 PM   #2
03heritagerider
Senior Member
 
Join Date: Dec 2008
Posts: 389
Default

Sugar,

I'll be watching your post carefully. I had one of my pads turn into a "Spear" on some soft ground and have had to use boards under it since.

I tried to get under there with a heavy ratchet, breaker bar, WD-40 and PB Blaster. I was going to try to just flip it over and use it that way. But, it would not budge.

I hope you get a response soon.
__________________
'03 41' Friendship & 24' trailer with HIS '03 H-D Heritage Springer, HER '15 H-D Freewheeler Trike, and '08 Smart Car.
"Adventure is found in the journey, not the destination."
03heritagerider is offline   Reply With Quote
Old 08-04-2010, 07:48 PM   #3
SugarRv
Junior Member
 
Join Date: Mar 2009
Location: Madison WI
Posts: 20
Default

The same thing happened to my pad. I contacted Power Gear and they basically said to just unbolt it from the bottom of the leg. I tried but had the same experience you had. I'm afraid if I put too much force on it, I might damage the leg, and that would be expensive. I am letting it sit for a couple of days after spraying it with Liquid Wrench.
__________________
2003 Friendship Quattro 41Ft
Cummins ISL 400
2012 Nissan Altima on Master Tow Dolly
SugarRv is offline   Reply With Quote
Old 08-04-2010, 10:05 PM   #4
03heritagerider
Senior Member
 
Join Date: Dec 2008
Posts: 389
Default

The only thing I didn't try, because I don't have one, is a an air impact wrench. If you have access to one, give that a try and let me know. If it works, it might be worth it for me to buy or rent one.
__________________
'03 41' Friendship & 24' trailer with HIS '03 H-D Heritage Springer, HER '15 H-D Freewheeler Trike, and '08 Smart Car.
"Adventure is found in the journey, not the destination."
03heritagerider is offline   Reply With Quote
Old 08-05-2010, 09:34 AM   #5
SugarRv
Junior Member
 
Join Date: Mar 2009
Location: Madison WI
Posts: 20
Default

Quote:
Originally Posted by 03heritagerider
The only thing I didn't try, because I don't have one, is a an air impact wrench. If you have access to one, give that a try and let me know. If it works, it might be worth it for me to buy or rent one.
Thanks for reminding me that I have an impact wrench. I will be gone the next few days but will give that a try when I return.
__________________
2003 Friendship Quattro 41Ft
Cummins ISL 400
2012 Nissan Altima on Master Tow Dolly
SugarRv is offline   Reply With Quote
Old 08-07-2010, 12:27 AM   #6
RayChez1
Senior Member
 
Join Date: Jun 2005
Posts: 1,257
Default

Yep, I also bent the rear pad on the drivers side. not real bad, but it is bent. I tried to pound it with a small sledge, but to no avail. I think maybe applying a little heat a person might be able to straighten it out. The only thing that might worry me about applying heat is that it might take the tensil out of the steal pad. Mine is not all that bent so I have not gotten into any rush to try and take it off.
__________________
2002 Gulf Stream Scenic Cruiser
2018 Buick Envision Essence
Neway Freightliner chassis
Aventa II Blue Ox
RayChez1 is offline   Reply With Quote
Old 08-07-2010, 08:21 AM   #7
03heritagerider
Senior Member
 
Join Date: Dec 2008
Posts: 389
Default

Ray,

Mine is also the rear driver's side pad. But it is definitely in a "V" shape. As, mentioned above, I put lumber under it to keep it from piercing into any surface. I also put lumber under the other pads to prevent them from bending also.

I think bending it back would only weaken the steel. If I were to ever get it off, I would install a new one, or go to a metal shop and get a heavier piece of steel to replace it.
__________________
'03 41' Friendship & 24' trailer with HIS '03 H-D Heritage Springer, HER '15 H-D Freewheeler Trike, and '08 Smart Car.
"Adventure is found in the journey, not the destination."
03heritagerider is offline   Reply With Quote
Old 08-24-2010, 05:48 PM   #8
SugarRv
Junior Member
 
Join Date: Mar 2009
Location: Madison WI
Posts: 20
Default

Quote:
Originally Posted by 03heritagerider
Ray,

Mine is also the rear driver's side pad. But it is definitely in a "V" shape. As, mentioned above, I put lumber under it to keep it from piercing into any surface. I also put lumber under the other pads to prevent them from bending also.

I think bending it back would only weaken the steel. If I were to ever get it off, I would install a new one, or go to a metal shop and get a heavier piece of steel to replace it.
A little heat did the trick for me. I used the propane torch for about 5 minutes and I was able to get the bolt to turn. I then heated the pad with the torch and pounded it flat with a 10# maul. It's 1/4 inch steel so I doubt if I weakened it at all. At least now it is back to flat and doing the job it was designed for.
__________________
2003 Friendship Quattro 41Ft
Cummins ISL 400
2012 Nissan Altima on Master Tow Dolly
SugarRv is offline   Reply With Quote
Old 08-24-2010, 07:13 PM   #9
03heritagerider
Senior Member
 
Join Date: Dec 2008
Posts: 389
Default

Sugar,

Thanks, I'll give it a try.
__________________
'03 41' Friendship & 24' trailer with HIS '03 H-D Heritage Springer, HER '15 H-D Freewheeler Trike, and '08 Smart Car.
"Adventure is found in the journey, not the destination."
03heritagerider is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Leveling Jacks ADGUY Class C 0 05-29-2017 09:31 AM
Supernova Cruising RPM Question, and MPG Question 38Chevy454 Class C 1 08-05-2013 10:39 PM
Equalizing systems leveling jacks question 68nova Class C 3 04-06-2010 07:38 PM
Leveling Jacks galena Class C 4 11-20-2008 10:22 AM
Leveling your RV Deryl Class A 3 09-27-2006 10:19 AM

» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 05:56 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
×