|
06-26-2020, 02:38 PM
|
#1
|
New Member
Join Date: Sep 2017
Location: Fort Worth
Posts: 11
|
Crown Molding Replacement
I am looking for advice on where to get a piece of crown molding. The original piece has some water damage and the vinyl is peeling away from the wood. I have checked home depot, lowes, and United RV and have come up empty and I need some ideas on how to fix this. The current molding is 1"x 5 1/2" x 27 3/4".
Thanks in advance for any ideas or advice.
Russell
|
|
|
06-26-2020, 06:11 PM
|
#2
|
Senior Member
Join Date: Nov 2012
Posts: 281
|
If you find some let me know, I couldn't even find it in Elkhart, I took a piece of trim from the bedroom & spliced it in then used something else in the bedroom, pressed board didn't like water
__________________
Mike & Becky
2005 Crescendo 8356
|
|
|
06-26-2020, 06:18 PM
|
#3
|
New Member
Join Date: Sep 2017
Location: Fort Worth
Posts: 11
|
Quote:
Originally Posted by Frutza
If you find some let me know, I couldn't even find it in Elkhart, I took a piece of trim from the bedroom & spliced it in then used something else in the bedroom, pressed board didn't like water
|
I found something at Home Depot but it was an inch short and had to improvise. I should have it installed tomorrow and I post a picture.
|
|
|
06-27-2020, 09:59 AM
|
#4
|
New Member
Join Date: Sep 2017
Location: Fort Worth
Posts: 11
|
Quote:
Originally Posted by Frutza
If you find some let me know, I couldn't even find it in Elkhart, I took a piece of trim from the bedroom & spliced it in then used something else in the bedroom, pressed board didn't like water
|
Attached are some pictures I took of the project. Because I could not find a piece of molding the correct width, I had to improvise an rip another board to place at the bottom. Color of stain is not perfect, but finished project looks ok.
|
|
|
07-05-2020, 12:20 PM
|
#5
|
New Member
Join Date: Nov 2011
Location: Henderson
Posts: 27
|
I hated the paper wrapped pressed board crown molding in our 2004 Atrium. Almost everything in the coach is solid oak except for this molding. I was going to make my own, but then I checked a specialty hardwood lumber dealer in town and they had solid oak molding in the correct size. I change all the crown molding in the coach.
|
|
|
07-06-2020, 03:34 PM
|
#6
|
Member
Join Date: Jan 2016
Posts: 51
|
Check out the "Molding Outlet" in LaPorte, IN. They have a molding factory there and the have a store in town that sells "seconds" at discount prices. All type and cuts of molding in Poplar and Oak. A visit there will want to make you build something.
|
|
|
07-09-2020, 09:51 AM
|
#7
|
New Member
Join Date: Dec 2010
Location: Mechanicsburg, Pa
Posts: 7
|
Quote:
Originally Posted by dangerruss
I am looking for advice on where to get a piece of crown molding. The original piece has some water damage and the vinyl is peeling away from the wood. I have checked home depot, lowes, and United RV and have come up empty and I need some ideas on how to fix this. The current molding is 1"x 5 1/2" x 27 3/4".
Thanks in advance for any ideas or advice.
Russell
|
I have the same problem. My question is, how is the crown molding attached to the wall. I would like to remove and replace it but don't want to damage the wall in the process.
__________________
Jamie
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|