Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
Gulf Stream Owners RV Forum
 


Reply
 
Thread Tools Search this Thread Display Modes
 
Old 11-24-2022, 05:45 PM   #1
RabbitStream
New Member
 
RabbitStream's Avatar
 
Join Date: Nov 2022
Posts: 15
Default Gulfstream tourmaster 1998 ball joints boots replacement

I own a 40 ft , TM on a Spartan Chassis with IFS and all 4 ball joints rubbers are torned aparts...but have no play on the attachments. So is they're is a way to protect those ball joints from dust and debris or else ( split boots or else...) then dismentle everything down...? Thank You...
RabbitStream is offline   Reply With Quote
Old 12-04-2022, 12:54 PM   #2
hossross
Senior Member
 
Join Date: Jul 2020
Location: Detroit
Posts: 125
Default

I don't know about aftermarket boots for ball joints, but try NAPA and Auto Zone to see what they have. The best thing to do for now is over grease the joint until grease is totally filled the cup as it is the water and grime from the outside that will accelerate wear. If it can't get in, then no contamination, just normal friction wear. The lower needs grease quickly already. If you can't find cover boots, Looks like the ball joints press into the knuckle, so you'll need specialized equipment for that and if this is coil springs and not leaf, then have a shop do it. Coil springs can be difficult to control with simple jacks. Maybe you have air springs, anyway if the spring is pushing on either the upper or lower arm there is a lot of force to support the front of the coach. Air should be easiest in that you can dump all the pressure and control the force that way. All this assumes that you will need to replace the boots, and you can take the knuckle off and take to a shop to install new ball joints. You would need to get toe set, so might as well check caster and camber too.
hossross is offline   Reply With Quote
Old 12-04-2022, 06:09 PM   #3
RabbitStream
New Member
 
RabbitStream's Avatar
 
Join Date: Nov 2022
Posts: 15
Default

Thank You...I still searching for a " split boot " for ball joint ...I read somewhere that it exist but do not remember Where ???
i still thinking about a way to protect the joining and that the frease stay put...
i appreciate your good advices...
RabbitStream is offline   Reply With Quote
Old 12-04-2022, 10:04 PM   #4
hossross
Senior Member
 
Join Date: Jul 2020
Location: Detroit
Posts: 125
Default

there are split inboard and outboard boots for the front wheel drive half shafts, but keep checking or fabricate your own with some of the new glues and materials, just remember that boot flexes up and down following movement of the arms and rotates or twists with the steering angle. Thats a lot of movement in such a small area. The one tear might be bonded with glueing the edge to edge or a patch, the upper look pretty gone. But clean up good so you can see what needs repaired and in you can get a good bond to the rubber. Glues are advertised to bond well enough to hold air in a tire. Could be worth a few bucks to give it a try if your going the route of boot repair.
hossross is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 11:09 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2023, vBulletin Solutions, Inc.
×