slide motor

I have a bt cruiser 2003. I have a problem with the slide. It is in and it will not go out. I bought it this way. I tried manually to move it out, but the gearbox or maybe a motor lock will not let this happen. I can’t really get to it with it in. I don’t know the brand, but it is a rack and...

I have an 06 Camelot 40PAQ and the flat floor living room slide is getting slower and slower to retract. The slide motor part number is Klauber k01285d300. I read somewhere that people are upgrading to Klauber k01285f350 which has more power. If you've done this upgrade could you comment? My...

Found two lag bolts out of the slide motor in the compartment below it. Motor seems to have a lot of torque when operating the slide and has pulled two lag bolts holding it out of the plywood. Anyone else had this issue and what did you do to fix it. Thank you

Hello, I have a 2022 BayStar 3014 with a Full Wall Slide on the driver's side. I ran into issues pulling the slide in several days ago and through a lot of diagnosing this is what I have figured out so far. I need help figuring out what to do to correct the issue now. When I put the KIB...

2006 Itasca Sunrise 35A. Where are the motors located for the main driver side slide. When I try to close slide it walks in about a foot then it stops. Panel flashes 6 times. I lubricanted under rails and rollers. I am able to push assist the slide in all the way by extending out first then hold...

My large slide motor K01431B300 has been surging for quite some time. When I asked Entegra service about it they told me my motor was getting weak and I should order a spare. Well, it finally started slipping gears with a loud grinding noise. I stopped immediately and replaced the slide motor...

2017 Entegra 44B. The drivers side slide is starting to slow down. Looking to replace it. The current motor is 7 rpm and I was thinking to upgrade to a little bit more rpm’s. Has anyone replaced there’s with a bigger motor??? Any info would be much appreciated. Thankyou.

I've found that there are rare occasions when the switch for my bedroom slide is "dead", and the solution is to "power-cycle" the bedroom slide control unit down in the basement. No rhyme or reason - it will work fine for months and then I'll go to close or open and it's "dead". Fortunately...

Has anyone replaced the driver's side bedroom slide motor on a 2008 Phaeton 36QSH? If so, how did you access the motor. Or is this something I need to take to a RV repair facility?

Am concerned about the bedroom slide motors. Currently I don't carry any with me while traveling. Thought about buying 2 of them, just in case. Getting ready for a 96-day outing in a 2015 Tiffin Allegro Red. Thoughts? Part Numbers? Amazon?

I recently had the slide motor on the driver's side big slide. I have the old motor and it seems to be working but I don't really know. How can I check to determine if the motor is good or bad. I have connected it to a 12v source and it runs in both directions but doesn't have a load on it so I...

I have a 99' Safari Continental with forward entry door, preety sure my slide motor has gone out. I can not find anything in the mauls on what motor it is. Any help would be appreciated.

!!!!! Warning, I have not tested this yet, I will in a week when I get back home. I was asking about a 00-971-100 Intellitec controller problem I was having. Use at your own risk. !!!!! Tech Tip from Intellitec tech support. "Newmar has had a very long history of problems with slideout...

Anyone ever swapped a 1285d300 slide motor and installed a 1285f350 on a Monaco or holiday or above floor slide. It was a mod done in about 2006 on new Monaco and HR as was determined the original 300 motor was not big enough. In monacoers archives p 158 in parts list this is described.

My kitchen slide would not pull up the incline on its own this morning. I gave it a push and it came in. When I go to my next stop I did some investigation. The Intellitec 00-971-100 controller is sending 17-18 amps to the motor when it is pulling up the incline. Troubleshooting guide on Newgle...

Looking for information on a replacement motor for the lounge slide on a 2005 National Tropical-cal T370 motor home. Mounting standoffs on motor assembly sheared off the mounting plate where gear on motor meshes with gear on shaft to drive the slide in/out. Current motor is RBW but no P/N...

Occasionally our PS rear slide would not retract. So, being in sunny Louisiana and after reading all previous post, I finally climbed under to remove the dreaded panel. 6 bolts and it fell off. I thought this is going to be easy. Pulled the first shear pin out, and tried the front pin and it...

Can anyone tell me where to locate the slide motor on my 2022 renegade Verona, thanks Mike

2018 NA 3341. Having a bit of a challenge finding access to the passenger side rear bedroom slide motor. Anyone have experience with this endeavor?

2018 Newmar new aire passenger side rear bedroom slide motor access

I have a 2014 bus and not near it right now and asking if any one knows the part number for the schwintek slide motor for my rear slides. Thanks for your time and info :popcorn:

Can anyone help me find an affordable replacement slide motor? The manufacturer wants $2000 for one. Attached is pictures with the current motor to show part numbers.

HI, I have an issue with slide out and need to manually crank it in. The manual mentions a place on the motor that is a lock release but I can't locate where the motor is located and the manual doesn't state where that is. Would appreciate any help!-thank you.

I have a 2007 Winnebago Sightseer 35J. It has a Kwikee slide, 2 rail system. The motor closest to the front of the motorhome is on its way out. It noisy and has a slight delay/ slowdown for a split second over and over again as it extends and retracts. the rails are clean and lubed. How do you...

A couple weeks ago I posted about an odd fast clicking sound I heard as I brought my large flat floor slide in on my 2013 4336 MA. Second time it did the same but failed with a squeal. Changed out the motor and autopsied the failed motor today. Appears both top and bottom bearings on a gear...